三重四极杆电感耦合等离子体质谱法测定K417合金中痕量硒和镉

doi:10.13228/j.boyuan.issn1000-7571.011676

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (1475 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要 K417合金中痕量Se和Cd的存在会严重影响其机械性能以及耐用性,因此准确测定其含量至关重要。采用电感耦合等离子体质谱法(ICP-MS)测定时,存在如⁶⁴Ni¹⁶O⁺对⁸⁰Se⁺以及⁹⁵Mo¹⁶O⁺对¹¹¹Cd⁺等质谱干扰,从而影响测定结果。实验采用盐酸-硝酸-氢氟酸在沸水浴中加热溶解样品,在三重四极杆(MS/MS)充O₂反应模式下,先分别设置一级质量过滤器(Q1)的质荷比(m/z)为80和111;再在碰撞反应池(CCT)中通入反应活性较大的O₂,将⁸⁰Se⁺、⁹⁵Mo¹⁶O⁺、⁹⁴Zr¹⁶O¹H⁺等与O₂反应生成⁸⁰Se¹⁶O⁺、⁹⁵Mo¹⁶O¹⁶O⁺、⁹⁴Zr¹⁶O¹⁶O¹H⁺,而⁶⁴Ni¹⁶O⁺、¹¹¹Cd⁺等不与O₂反应;最后设置二级质量过滤器(Q2)的质荷比分别为96和111,利用质量转移法(Mass shift)和原位法(On mass)使⁸⁰Se¹⁶O⁺、¹¹¹Cd⁺通过并被检测,从而避免了质谱干扰。据此,建立了三重四极杆电感耦合等离子体质谱法(ICP-MS/MS)测定K417合金中Se和Cd的方法。对O₂流量进行了优化,分别选择O₂流量为0.3 mL/min时测定Se和0.9 mL/min时测定Cd,同时在内标溶液中加入6%(体积分数)的异丙醇作为基体改进剂以提高试验的灵敏度和稳定性。Se的线性范围为0.018~100.0 μg/L,Cd为0.001~5.0 μg/L,线性相关系数均为0.999;Se和Cd的检出限分别为0.018 μg/g和0.000 8 μg/g,定量限分别为0.058 μg/g和0.002 7 μg/g。按照实验方法对高温合金标准物质中Se和Cd进行测定,测定结果与认定值一致。对K417合金样品中Se和Cd进行测定,测定结果与辉光放电质谱法相一致,其相对标准偏差(RSD,n=6)分别为2.2%和14.9%。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	王艳萍
	年季强
	朱杰
	荆淼

关键词 ：三重四极杆, 电感耦合等离子体质谱法(ICP-MS), 质量转移法, 原位法, K417合金, 硒, 镉

Abstract：The presence of trace selenium (Se) and cadmium (Cd) in K417 alloy can severely affect its mechanical property and durability. Therefore, the accurate determination of Se and Cd contents is of great significance. During the determination of Se and Cd by inductively coupled plasma mass spectrometry (ICP-MS), the interference of ⁶⁴Ni¹⁶O⁺ with ⁸⁰Se⁺ and ⁹⁵Mo¹⁶O⁺ with ¹¹¹Cd⁺ will influence on the determination results. In experiments, the sample was dissolved with hydrochloric acid-nitric acid-hydrofluoric acid in boiling water bath. The mass-to-charge ratio (m/z) of the first-order mass filter (Q1) was set as 80 and 111 at the reaction mode of triple quadrupole (MS/MS) filling with O₂. Then O₂ with high reactivity was injected into collision/reaction cell (CCT). ⁸⁰Se⁺, ⁹⁵Mo¹⁶O⁺ and ⁹⁴Zr¹⁶O¹H⁺ could react with O₂ to form ⁸⁰Se¹⁶O⁺, ⁹⁵Mo¹⁶O¹⁶O⁺ and ⁹⁴Zr¹⁶O¹⁶O¹H⁺, respectively. Meanwhile, ⁶⁴Ni¹⁶O⁺ and ¹¹¹Cd⁺ could not react with O₂. Finally, the m/z of the second-order mass filter (Q2) was set as 96 and 111, respectively. ⁸⁰Se¹⁶O⁺ and ¹¹¹Cd⁺ were passed and detected by the mass shift method and on mass method, which avoided the mass spectrum interference. Based on these results, a method for the determination of Se and Cd in K417 alloy by triple quadrupole inductively coupled plasma mass spectrometry (ICP-MS/MS) was established. The flow rate of O₂ was optimized and selected at 0.3 mL/min for Se and 0.9 mL/min for Cd, respectively. Meanwhile, 6% (volume fraction) isopropanol was added into internal standard solution as the matrix modifier to enhance the experimental sensitivity and stability. The linear range was 0.018-100.0 μg/L for Se and 0.001-5.0 μg/L for Cd. The linear correlation coefficients were 0.999. The limit of detection for Se and Cd was 0.018 μg/g and 0.000 8 μg/g, and the limit of quantification was 0.058 μg/g and 0.002 7 μg/g, respectively. The contents of Se and Cd in certified reference material of high temperature alloy were determined according to the experimental method, and the found results were consistent with the certified values. The contents of Se and Cd in K417 alloy sample were determined, and the found results were basically consistent with those obtained by the glow discharge mass spectrometry (GD-MS). The relative standard deviation (RSDs, n=6) was 2.2% and 14.9%, respectively.

Key words： triple quadrupole inductively coupled plasma mass spectrometry (ICP-MS) mass shift on mass K417 alloy selenium cadmium

收稿日期: 2021-11-10

ZTFLH:	O657.63
	TF125.2+12

基金资助:国家科技重大专项(2017-VI-0013-0085)

通讯作者: 年季强(1982—),男,高级工程师,硕士,研究方向为冶金分析;E-mail:nian1210@163.com

作者简介: 王艳萍(1981—),女,高级工程师,硕士,研究方向为无机重金属元素及形态分析;E-mail:wangyp588@163.com

引用本文:

王艳萍, 年季强, 朱杰, 荆淼. 三重四极杆电感耦合等离子体质谱法测定K417合金中痕量硒和镉[J]. 冶金分析, 2022, 42(7): 10-18. WANG Yanping, NIAN Jiqiang, ZHU Jie, JING Miao. Determination of trace selenium and cadmium in K417 alloy by triple quadrupole inductively coupled plasma mass spectrometry. , 2022, 42(7): 10-18.

链接本文:

http://yjfx.chinamet.cn/CN/10.13228/j.boyuan.issn1000-7571.011676 或 http://yjfx.chinamet.cn/CN/Y2022/V42/I7/10

[1] 王慢慢,杨彦红,王道红,等.铸造高温合金K417G深度脱氧脱硫的研究[J].稀有金属材料与工程,2018,47(12):3730-3734.
WANG Manman,YANG Yanhong,WANG Daohong,et al.Deep deoxidation and desulfurization of cast superalloy K417G[J].Rare Metal Materials and Engineering,2018,47(12):3730-3734.
[2] 郭建亭.高温合金材料学[M].北京:科学出版社,2008.
[3] 马冲先,陈忠颖,芮琦.镍基高温合金中痕量元素的分析方法研究的最新进展[J].理化检验(化学分册),2013,49(12):1522-1531.
MA Chongxian,CHEN Zhongying,RUI Qi.Recent progress of researches on methods for determination of trace elements in nickel-based superalloys[J].Physical Testing and Chemical Analysis(Part B:Chemical Analysis),2013,49(12):1522-1531.
[4] 耿东方,罗虹,严永茂,等.平台石墨炉原子吸收法测定高温镍基合金中痕量硒[J].兵器材料科学与研究,2002,25(4):48-50.
GENG Dongfang,LUO Hong,YAN Yongmao,et al.To determine trace Se in high temperature Ni base alloy with graphite furnace atomic absorption spectrophotometry(GFAAS) method[J].Ordnance Material Science and Engineering,2002,25(4):48-50.
[5] 颜京,张佩佩,汪磊,等.电感耦合等离子体原子发射光谱法测定高温合金中镉[J].化学分析计量,2020,29(Z1):60-62.
YAN Jing,ZHANG Peipei,WANG Lei,et al.Determination of cadmium in superalloy by inductively coupled plasma atomic emission spectrometry[J].Chemical Analysis and Meterage,2020,29(Z1):60-62.
[6] 张晓寒,马冲先,李莎莎,等.氢化物发生-原子荧光光谱法在金属及合金中痕量元素测定方面的最新进展[J].理化检验(化学分册),2014,50(6):784-790.
ZHANG Xiaohan,MA Chongxian,LI Shasha,et al.Recent progress of application of HG-AFS to determination of trace elements in merals and alloys[J].Physical Testing and Chemical Analysis(Part B:Chemical Analysis),2014,50(6):784-790.
[7] 干宁,李天华,王鲁雁,等.流动注射氢化物发生与动态反应池-电感耦合等离子体质谱法分析镍基超合金中锗砷硒[J].冶金分析,2007,27(11):7-11.
GAN Ning,LI Tianhua,WANG Luyan,et al.Determination of germanium, arsenic, selenium in nickel-base superalloy by flow injection hydride generation and dynamic reaction cell-inductively coupled plasma mass spectrometry[J].Metallurgical Analysis,2007,27(11):7-11.
[8] 胡净宇,王海舟.激光剥蚀-电感耦合等离子体质谱对高温合金中17种痕量元素的测定[J].分析测试学报,2010,29(4):359-363.
HU Jingyu,WANG Haizhou.Determination of 17 trace elements in nickel-base superalloy by laser ablation inductively coupled plasma mass spectrometry[J].Journal of Instrumental Analysis,2010,29(4):359-363.
[9] 杨国武,侯艳霞,刘庆斌,等.萃取分离-电感耦合等离子体质谱法测定高温合金中痕量镉[J].冶金分析,2019,39(4):1-6.
YANG Guowu,HOU Yanxia,LIU Qingbin,et al.Determination of trace cadmium in superalloy by extraction separation-inductively coupled plasma mass spectrometry[J].Metallurgical Analysis,2019,39(4):1-6.
[10] 包香春,李建亭,刘春,等.电感耦合等离子体质谱法测定镍铬合金中砷硒锡锑铅铋[J].冶金分析,2021,41(11):37-42.
BAO Xiangchun,LI Jianting,LIU Chun,et al.Determination of arsenic,selenium,tin,antimony,lead and bismuth in nickel-chromium alloy by inductively coupled plasma mass spectrometry[J].Metallurgical Analysis,2021,41(11):37-42.
[11] 马晓龙,李刚,李艳,等.碰撞反应池-电感耦合等离子体质谱法测定锆基合金中痕量镉[J].理化检验(化学分册),2014,50(3):345-348.
MA Xiaolong,LI Gang,LI Yan,et al.Determination of trace cadmium in zirconium-based alloys by impact reactor inductively coupled plasma-mass spectrometry[J].Physical Testing and Chemical Analysis (Part B:Chemical Analysis),2014,50(3):345-348.
[12] 胡净宇,王海舟.电感耦合等离子体质谱法测定高温合金中痕量镉和碲[J].冶金分析,2010,30(2):8-12.
HU Jingyu,WANG Haizhou.Determination of trace cadmium and tellurium in superalloy by inductively coupled plasma mass spectrometry[J].Metallurgical Analysis,2010,30(2):8-12.
[13] Balcaen L,Bolea Fernandez E,Resano M,et al.Inductively coupled plasma-tandem mass spectrometry(ICP-MS/MS):a powerful and universal tool for the interference-free determination of (ultra) trace elements-a tutorial review[J].Analytica Chimica Acta,2017,32:1660-1679.
[14] 李金蔓,张贵伟,陈树娣,等.异丙醇基体改进剂用于微波消解-ICP-MS测定芹菜、圆白菜、鸡肉和猪肝中微量硒[J].食品工业科技,2016,37(19):307-310.
LI Jinman,ZHANG Guiwei,CHEN Shudi,et al.Determination of selenium in celery,cabbage,chicken and liver with isopropanol as matrix modifier by microwave digestion-inductively coupled plasma mass spectrometry[J].Science and Technology of Food Industry,2016,37(19):307-310.
[15] 赵志飞,任小荣,李策,等.氧气反应模式-电感耦合等离子体串联质谱法测定土壤中的镉[J].岩矿测试,2021,40(1):95-102.
ZHAO Zhifei,REN Xiaorong,LI Ce,et al.Determination of cadmium in soil samples by ICP-MS/MS using oxygen reaction mode[J].Rock and Mineral Analysis,2021,40(1):95-102.
[16] 郭红巧,胡净宇,侯艳霞,等.电感耦合等离子体串联质谱法测定高温合金中痕量磷和硫[J].冶金分析,2021,41(11):1-7.
GUO Hongqiao,HU Jingyu,HOU Yanxia,et al.Determination of trace phosphorus and sulfur in superalloy by inductively coupled plasma tandem mass spectrometry[J].Metallurgical Analysis,2021,41(11):1-7.
[17] 郭红巧,胡净宇,侯艳霞,等.电感耦合等离子体串联质谱法测定高温合金中痕量砷[J].冶金分析,2021,41(5):35-40.
GUO Hongqiao,HU Jingyu,HOU Yanxia,et al.Determination of trace arsenic in superalloy by inductively coupled plasma tandem mass spectrometry[J].Metallurgical Analysis,2021,41(5):35-40.
[18] 徐娜.电感耦合等离子体串联质谱法直接测定稀土产品中的痕量砷、硒[C]//2017年第十六届全国稀土分析化学学术研讨会论文集.厦门:中国稀土学会理化检验专业委员会和中国稀土行业协会检测与标准分会,2017:27.
[19] Kenghsien Su,Wang Xinwei,Karol Putyera.高流速辉光放电质谱法检测镍基高温合金中痕量元素及其深度分布[J].冶金分析,2011,31(11):18-23.
Kenghsien Su,Wang Xinwei,Karol Putyera.Depth resolved trace element analysis of Ni-base superalloys using fast flow-glow discharge mass spectrometry(FF-GDMS) [J].Metallurgical Analysis,2011,31(11):18-23.