Abstract:The accurate determination of palladium content in palladium-containing alloy is of great significance for the quality control and market trade of products.The determination of palladium in palladium-containing alloy usually adopts dimethylglyoxime EDTA complexometric titration or dimethylglyoxime gravimetry.However,these methods have some problems of visual error easily caused by endpoint judgement with eyes or long procedures in operation.In this study,after dissolving the palladium-containing alloy,excessive EDTA solution was added into sample solution to complex palladium and coexisting ions.The excess EDTA was titrated with zinc standard titration until the solution color changed from yellow to red yellow, i.e.,the first endpoint.At this time,the titration volume did not participate in the calculation of results.Thiourea solution was added to complex palladium in palladium-EDTA.Same amount of EDTA to palladium was released,which was then titrated with zinc standard titration solution until the solution color changed from orange yellow to red yellow,i.e.,the second endpoint.The absorbance change was converted to the electrical signal change using photometric titrimeter to judge the titration endpoint.Consequently,a new method for the determination of palladium in palladium-containing alloy by photometric titration was established.AgPd30,AgPdCu20-28,AuPd20,AuPdNi8-22,PdW18 and PdNi40 were dissolved,and the palladium contents were determined according to the experimental method.Moreover,the palladium standard solution was added for recovery test.The results showed that the palladium content(mass fraction,the same below) in sample was in range of 7.83%-81.61%.The relative standard deviations (RSDs,n=7) of determination results were between 0.09% and 0.36%,the recoveries were between 99.6% and 100.3%.The contents of palladium in PdW18,PdNi40,AgPd30,AgPdCu20-28,AuPd20 and AuPdNi8-22 were determined for 7 times in parallel by the experimental method and industrial standard method(YS/T 372.3-2006).The found results of two methods were basically consistent.
[1] 彭伟,彭戴,孙立志.钯元素分析方法的研究进展[J].船电技术,2017,37(5):15-19. PENG Wei,PENG Dai,SUN Lizhi.Research progress of analytical methods for the palladium[J].Marine Electric & Electronic Engineering,2017,37(5):15-19. [2] 侯君钊,张圣欢,闫爽,等.钯含量分析方法研究进展[J].化学分析计量,2021,30(12):89-94. HOU Junzhao,ZHANG Shenghuan,YAN Shuang,et al.A research progress of analysis methods for contents of palladium[J].Chemical Analysis and Meterage,2021,30(12):89-94. [3] 中华人民共和国国家发展和改革委员会,中国国家标准化管理委员会.YS/T 372.3—2006贵金属合金元素分析方法 钯量的测定 丁二酮肟析出EDTA络合滴定法[S].北京:中国标准出版社,2006. [4] 朱利亚.银合金中钯铜连续测定的研究[J].云南冶金,1993,22(4):52-56. ZHU Liya.Study on continuous determination of palladium-copper in silver alloys[J].Yunnan Metallurgy,1993,22(4):52-56. [5] 中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.GB/T 215072.4—2008 贵金属合金化学分析方法 钯、银合金中钯量的测定 二甲基乙二醛肟重量法[S].北京:中国标准出版社,2008. [6] 邢银娟,杨军红,甘建壮,等.自动电位滴定仪测定氯化钯中钯量[J].广州化工,2019,47(6):78-79. XING Yinjuan,YANG Junhong,GAN Jianzhuang,et al.Determination of palladium in palladium chloride by automatic potentiometric titrator[J].Guangzhou Chemical Industry,2019,47(6):78-79. [7] Raoot K N,Raoot S.Selective complexation titration for thiourea masking of palladium[J].Talanta,1981,28(5):327-328. [8] 黄树茂.金基合金中钯的络合滴定[J].化学计量,1996,5(1):24-28. HUANG Shumao.Complexometric titration of palladium in gold-based alloys[J].Chemical and Meterage,1996,5(1):24-28. [9] 喻银谷.镍基合金中钯的快速测定[J].冶金分析,2000,20(6):20. YU Yingu.Rapid determination of palladium in nickel-based alloys[J].Metallurgical Analysis,2000,20(6):20. [10] 黄树茂.铜存在下络合滴定钯[J].贵金属,1996,17(2):43-45. HUANG Shumao.When palladium is complexed titration contains copper[J].Precious Metals,1996,17(2):43-45. [11] 中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.GB/T 215072.8—2008 贵金属合金化学分析方法 金、钯、银合金中铜量的测定 硫脲析出EDTA络合返滴定法[S].北京:中国标准出版社,2008. [12] 马王蕊,姚艳波,林波,等.萃取分离-重量法和电感耦合等离子体原子发射光谱法分别测定金铂废液中金和铂[J].冶金分析,2022,42(12):52-59. MA Wangrui,YAO Yanbo,LIN Bo,et al.Respective determination of gold and platinum in gold-platinum waste liquid by gravimetry and inductively coupled plasma atomic emission spectrometry with extraction separation[J].Metallurgical Analysis,2022,42(12):52-59.