高频燃烧-红外吸收法测定镍基自熔合金中碳

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (829 KB) HTML (0 KB)
输出: BibTeX | EndNote (RIS)

摘要介绍了高频燃烧-红外吸收法测定FZNCr-60A镍基自熔合金中碳的方法。对助熔剂的种类、加入方式以及用量做了较详细的研究，同时试验了不同的样品称样量和加入顺序，确定了先加0.3g铁助熔剂，然后加0.2g试样，最后加1.5g钨锡助熔剂的最佳的加入顺序。在没有FZNCr-60A镍基自熔合金标准样品的情况下，选择含量接近的LECO501-506钢铁中碳和硫校准样品(w(C)=0.895%±0.007%)以及其他合金标样对仪器进行了校准。将实验确定的方法用于两个含量不同的实际样品中碳的测定，测得结果分别为0.857%和0.816%，相对标准偏差小于0.18%(n=11)，加标回收率在99%～101%之间。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章

关键词 ：镍基自熔合金, 碳, 高频燃烧-红外吸收法

Abstract：A method was described for the determination of carbon in nickel-matrix self-fluxing alloy by high-frequency combustion - infrared absorption. The type,adding method and dosage of the flux were studied in detail,meanwhile the dosages and adding sequence of different samples were tested,and the optimum adding sequence was determined as 0.3 g of iron,0.2 g of the sample and finally 1.5 g of tungsten-tin flux. In the absence of certified reference materials for FZNCr-60A nickel-based self-fluxing alloy,the the calibration samples( LECO 501-506) with similar content of carbon and sulfur (w(C)=0.895%±0.007%) and certified reference materials of other alloys were used to calibrate the instrument. The experimental method was used to determine the carbon content of two actual samples with different contents and the measured results were 0.857 % and 0.816 %,with the relative standard deviation less than 0.18% (n=11) and the recovery rate in the range of 99%-101%.

Key words： nickel-based self-fluxing alloy carbon high frequency combustion-infrared absorption method

收稿日期: 2013-11-28

ZTFLH:

O659.2

作者简介: 郑立春(1979-),男,工程师,主要从事金属测试分析;E-mail:zhengjingzhe1979@sina.com

引用本文:

郑立春，张庸，闫秀芬，张继民，杨丽，詹秀嫣，李继超. 高频燃烧-红外吸收法测定镍基自熔合金中碳[J]. 冶金分析, 2013, 33(11): 67-70. ZHENG Li-chun,ZHANG Yong,YAN Xiu-fen ZHANG Ji-min,YANG Li,ZHAN Xiu-yan,LI Ji-chao. Determination of carbon in nickel-matrix self-fluxing alloy by high frequency-infrared absorption method. , 2013, 33(11): 67-70.

链接本文:

http://47.93.29.245/Jweb_yjfx/CN/ 或 http://47.93.29.245/Jweb_yjfx/CN/Y2013/V33/I11/67


[1]	袁庆龙,苏志俊. 高硬度镍基自熔合金涂层高频感应重熔研究[J]. 热加工工艺(Hot Working Technology), 2009, 38(8):73-75.

[2]	赵国城. 延缓燃烧法应用于直接燃烧-气体容量法测定不锈钢中低碳含量[J]. 理化检验:化学分册(Physical Testing and Chemical Analysis :Part B Chemical Analysis), 2008,44(9):896-897.

[3]	陈晓青, 邓大超. 方彩云. 金属中碳的分析方法综述[J]. 冶金分析(Metallurgical Analysis),2003, 23(2):31-37.

[4]	蒋启翠. 高频燃烧-红外吸收法测定钢铁中微量碳硫[J]. 冶金分析(Metallurgical Analysis),2005, 25(4):95-96.

[5]	钟华. 纯化学物质校准—高频燃烧红外吸收法测定钛及钛合金中碳[J].冶金分析(Metallurgical Analysis), 2012, 32(3):30-34.

[6]	赵宇, 宋立伟. 红外吸收法测定钼铁中碳硫[J]. 冶金分析(Metallurgical Analysis), 2003, 23(1):53-54.

[7]	李兰群, 尹艳清. 高频感应燃烧-红外吸收法测定复合碳硅锰铁合金中碳和硫[J]. 冶金分析(Metallurgical Analysis),2010, 30(6):62-65.

[8]	柳轶男, 姜立强, 张书菊. CS-800红外碳硫分析测定合金钢中的碳和硫[J]. 光谱实验室(Chinese Journal of Spectroscopy Laboratory), 2011,28(4):1958-1962.

[9]	刘淑珍. 高频红外碳硫分析助熔剂选择[J]. 冶金分析(Metallurgical Analysis),1991, 11(5):45-47.

[10]	胡正阳,邢华宝,华静,等. 生铁异标校正红外吸收法测定硅锰中碳、硫[J]. 冶金分析(Metallurgical Analysis), 2002,22(6):45-46.

[11]	胡正阳, 邢华宝, 叶春晖. 生铁异标校正红外吸收测定硅锰中碳、硫[J]. 钢铁(Steel), 2002, 37(增刊):910-912.